หน้าแรก | ติดต่อเรา | ข่าวสาร | เว็บบอร์ด | เกี่ยวกับเรา | วิธีการชำระเงิน | วิธีการสั่งซื้อ      
            ตั้งเป็นหน้าแรก    เครื่องคิดเลข    แจ้งการชำระเงิน         ไทย | English    
   หมวดหมู่สินค้า
แสดงสินค้าทั้งหมด (4191)
สินค้าขายดี (146)
สินค้ามาใหม่ (158)
Energy
AUTEL ROBOTIC
โปรโมชั่น
01 DJI INNOVATIONS
Gopro Camera
DJI Accessories
Tiger Motors
SEETEC
Feelworld/SeeTec monitor
feiyu-tech
FAT SHARK Goggle
Protect Case กระเป๋า
TAROT Multirotor
FPV Racing
Dragonlink system
Flex Innovations & AJ Aircraft
FMS Model
XFly Model
AV DIGITAL
FPV/UAV Systems
Multirotor & Parts
ManiaX Lipo
Multirotor & Parts
เครื่องบินไฟฟ้า-น้ำมัน Airplane
เฮลิคอปเตอร์ไฟฟ้า-น้ำมัน Helicopter
มอเตอร์ไฟฟ้า Motors
  - Outrunner motor
  - Inrunner motor
  - EDF systems
  - Turnigy motor
  - Scorpion Motors
สปีดคอนโทรล - Speed control
วิทยุรับ-ส่ง (Remote Controller)
เครื่องยนต์และอะไหล่ Engine & parts
เซอร์โวและชุดซ่อม
แบตเตอรี่-เครื่องชาร์จ
ไจโร,BEC & Governer
น้ำมัน-ไนโตร
เครื่องมือ-เครื่องวัด
โปรแกรมฝึกบิน
ใบพัดเครื่องบิน Propeler
เบลดเฮลิคอปเตอร์ Heli Blade
อุปกรณ์ประกอบ-อี่นๆ
อะไหล่-ชุดแต่ง Trex
อะไหล่ Copter X
อะไหล่-ชุดแต่ง เฮลิคอปเตอร์ไฟฟ้า
อะไหล่เฮลิคอปเตอร์น้ำมัน
รถยนต์-มอเตอร์ไซค์
สินค้าลดราคา
Speed Airboat
หนังสือ
เทป+กาว
สินค้าฝากขาย
Drone mini
   สมาชิก
อีเมล์ : 
รหัสผ่าน : 
 
 สมัครสมาชิก
 ลืมรหัสผ่าน
   เว็บเพื่อนบ้าน
RC Thai
Bangkokdomain


ร้านบูรพาทอย
ทางใหม่ซอฟ
DJI-Innovations
กระเป๋าสำหรับ DJI Avata มีหลายแบบ คลิกเลย


 
รหัสสินค้า : HK_4025_5mm_Shaft
Scorpion HK-4025 Motor Shaft Kit (5 mm)
สถานะสินค้า : สินค้าพร้อมส่ง
ราคา ฿330.00   หยิบใส่ตะกร้า

The Scorpion HK-4025 motors are built with 8mm hardened steel shafts that will last through countless hours of flying fun, but occasionally, on a "Less than Perfect" landing, you may bend or break one. For these occasions, we offer factory replacement shafts for all the HK-4025 series Scorpion Helicopter Motors

The shaft for the HK-4025 series motors measures 8mm in diameter, and is 83.7mm in long. The Stock HK-4025 motors have a 5mm output shaft end on them to allow the user to install 5mm pinion gears. The shaft kit will also fit other brushless motors that require an 8mm shaft of this length with 5mm end. The shafts can be cut shorter with a Dremel tool and a cut-off wheel if necessary to fit other motors.

Note: The shafts in the Scorpion motors are a slight press fit into the aluminum front housing. The shafts will not just slide out when the setscrews are removed. They need to be pressed out in a bearing press, or in a drill press, with the front housing of the motor supported in a block of wood to prevent warping the front housing.

Included in the Box

- HK4025 Motor Shaft (5mm) x1
- Washer x 1
- C-Clip x 2

Weight including packaging

28g

 

[540322]


:: เข้าชม 2850 :: ข้อมูลล่าสุด 14/07/2566 ::กลับ  |  ขึ้นด้านบน  |   ส่งให้เพื่อน   
ร้านทวินโปร ฮ้อบบี้ จำหน่ายเครื่องบินบังคับวิทยุ, เฮลิคอปเตอร์บังคับวิทยุ และอุปกร์ RC ทุกชนิด   You are visitor no. 35,011,866  ออนไลน์ : 23
E-commerce Solutions by BangkokDomain.com   ®